Advertisement
Not a member of Pastebin yet?
Sign Up,
it unlocks many cool features!
- # This file contains common pin mappings for RAMPS (v1.3 and later)
- # boards. RAMPS boards typically use a firmware compiled for the AVR
- # atmega2560 (though other AVR chips are also possible).
- # See the example.cfg file for a description of available parameters.
- [stepper_x]
- step_pin: ar54
- dir_pin: ar55
- enable_pin: !ar38
- step_distance: .05
- endstop_pin: ^ar3
- position_endstop: 0
- position_min: 0
- position_max: 230
- homing_speed: 60
- [tmc2208 stepper_x]
- uart_pin: ar63
- microsteps: 4
- run_current: 0.7
- hold_current: 0.3
- stealthchop_threshold: 125
- [stepper_y]
- step_pin: ar60
- dir_pin: ar61
- enable_pin: !ar56
- step_distance: .05
- endstop_pin: ^ar14
- position_endstop: 0
- position_min: 0
- position_max: 230
- homing_speed: 60
- [tmc2208 stepper_y]
- uart_pin: ar64
- microsteps: 4
- run_current: 0.7
- hold_current: 0.3
- stealthchop_threshold: 125
- [stepper_z]
- step_pin: ar46
- dir_pin: !ar48
- enable_pin: !ar62
- step_distance: .01
- endstop_pin: ^ar18
- position_endstop: 0
- position_min: 0
- position_max: 220
- homing_speed: 20
- [tmc2208 stepper_z]
- uart_pin: ar65
- microsteps: 4
- run_current: 0.7
- hold_current: 0.3
- stealthchop_threshold: 50
- [extruder]
- step_pin: ar26
- dir_pin: ar28
- enable_pin: !ar24
- step_distance: 0.0425
- nozzle_diameter: 0.400
- filament_diameter: 1.75
- max_extrude_cross_section: 0.90
- pressure_advance: 0.10
- pressure_advance_lookahead_time: 0.01
- heater_pin: ar10
- sensor_type: EPCOS 100K B57560G104F
- sensor_pin: analog13
- control: pid
- smooth_time: 2
- max_power: 1.0
- pid_Kp: 21.527
- pid_Ki: 1.063
- pid_Kd: 108.982
- min_temp: 0
- min_extrude_temp: 120
- max_temp: 260
- [tmc2208 extruder]
- uart_pin: ar66
- microsteps: 4
- run_current: 0.6
- hold_current: 0.2
- stealthchop_threshold: 0
- [heater_bed]
- heater_pin: ar8
- sensor_type: EPCOS 100K B57560G104F
- sensor_pin: analog14
- control: pid
- pid_Kp: 54.027
- pid_Ki: 0.770
- pid_Kd: 948.182
- min_temp: 0
- max_temp: 130
- [fan]
- pin: ar9
- max_power: 1.0
- cycle_time: 0.05
- kick_start_time: 0.0
- [mcu]
- serial: /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_A907K8EE-if00-port0
- pin_map: arduino
- [printer]
- kinematics: cartesian
- max_velocity: 400
- max_accel: 3150
- max_z_velocity: 40
- max_z_accel: 1250
- square_corner_velocity: 5.0
- [probe]
- pin: ar19
- x_offset: -28.65
- y_offset: -8.75
- z_offset: -2.06
- [bed_mesh]
- speed: 50
- horizontal_move_z: 5
- samples: 3
- sample_retract_dist: 5
- min_point: 10,10
- max_point: 190,190
- probe_count: 5,5
- [virtual_sdcard]
- path: ~/.octoprint/uploads
- [homing_override]
- gcode: G28 Z0
- G1 Z10 F600
- G28 X0
- G28 Y0
- G28 Z0
- axes: xyz
Advertisement
Add Comment
Please, Sign In to add comment
Advertisement
